top of page

Support Group

Public·53 members

Hc-700 M G Software Download


HC-700 M/G Software Download: How to Set Up and Use Your Trail Camera




If you are looking for a reliable and affordable trail camera that can send photos and videos to your email or phone, you might want to consider the HC-700 M/G model from Suntek. This camera has a 16MP resolution, a 0.5s trigger speed, a 20m flash range, and a built-in 2.0" TFT color screen. It also supports 2G (GSM) or 3G (WCDMA) network, depending on the version you choose.


However, before you can enjoy the features of this camera, you need to download and install the software that allows you to configure the camera settings and send photos via SMTP protocol. In this article, we will show you how to do that step by step. We will also give you some tips on how to set up and use your HC-700 M/G trail camera effectively.




hc-700 m g software download


Download Zip: https://imgfil.com/2vMOVP



Introduction




What is HC-700 M/G trail camera?




The HC-700 M/G trail camera is a digital device that can capture images and videos of wildlife or other subjects in remote areas. It has a motion sensor that detects any movement within its detection range and triggers the camera to take a photo or record a video. The camera can also send the photo or video to your email or phone via 2G or 3G network, depending on the version you have.


The HC-700 M/G trail camera has several features that make it suitable for various applications, such as hunting, wildlife observation, security surveillance, farm monitoring, etc. Some of these features are:



  • Built-in 2.0" TFT color screen to review photos and videos on camera



  • 32pcs IR LEDs for flash range as 20 meters



  • Programmable 8/12/16 Megapixel high-quality resolution



  • Color pictures during daylight; black and white at night



  • Adjustable PIR sensitivity; HIGH, MID, LOW



  • Impressive quick trigger time: 0.5s



  • Multi-shot pictures; 1, 3, 6, 9



  • Adjustable delay between motions; 1/5/10/30 seconds/minutes



  • Adjustable video length; 10/30/60/90 seconds



  • With 8 AA alkaline batteries, the longest standby time is up to 6 months



  • Available operation temperature: -30 to 50



  • With specified timer, camera can be programmed to work only during preset time period every day



  • Stamp of date, time, temperature and moon phase on every picture



  • Password protection



  • Supports SD card up to 64GB



  • Waterproof IP54



Why do you need to download the software?




The HC-700 M/G trail camera comes with a CD that contains a free program called MMSConfig. This program allows you to configure the camera settings and send photos via SMTP protocol. SMTP stands for Simple Mail Transfer Protocol, which is a standard method of sending emails over the internet. By using SMTP, you can send photos to your email or phone without using a third-party service or app. This can save you time and money, and also protect your privacy and security.


How to download and install the software?




To download and install the software for your HC-700 M/G trail camera, you need to follow these steps:



  • Insert the CD that came with your camera into your PC's CD drive. If you don't have a CD drive, you can download the software from [this link](^1^).



  • Open the CD folder and find the file named MMSConfig.exe. Double-click on it to run the program.



  • Follow the instructions on the screen to install the software on your PC. You may need to restart your PC after the installation is complete.



  • Launch the MMSConfig program from your desktop or start menu. You will see a window like this:




This is the main interface of the software, where you can configure the camera settings and send photos via SMTP protocol. We will explain how to use it in the next section.


How to Set Up Your HC-700 M/G Trail Camera




Inserting the SIM card, SD card, and batteries




Before you can use your HC-700 M/G trail camera, you need to insert a SIM card, an SD card, and batteries into it. Here is how to do it:



  • Open the bottom cover of the camera by sliding it downwards. You will see three slots: one for the SIM card, one for the SD card, and one for the batteries.



  • Insert a SIM card that supports 2G (GSM) or 3G (WCDMA) network, depending on the version of your camera. Make sure the SIM card has enough balance and data traffic service. The SIM card slot is located on the left side of the camera, next to the USB port. Push the SIM card into the slot until it clicks into place.



  • Insert an SD card (up to 64GB) that stores the photos and videos captured by the camera. The SD card slot is located on the right side of the camera, next to the power switch. Push the SD card into the slot until it clicks into place.



  • Insert eight AA batteries that power the camera. The battery slot is located at the bottom of the camera, under a plastic cover. Open the cover by pressing on both sides and lifting it up. Insert the batteries according to the polarity marks (+ and -) inside the slot. Close the cover by pressing it down until it clicks into place.



  • Close the bottom cover of the camera by sliding it upwards until it locks securely.



Connecting the camera to your PC




To configure the camera settings and send photos via SMTP protocol, you need to connect your camera to your PC with a USB cable. Here is how to do it:



  • Turn off your camera by sliding the power switch to OFF position.



  • Connect one end of the USB cable to your camera's USB port, which is located on the left side of the camera, next to the SIM card slot.



  • Connect the other end of the USB cable to your PC's USB port.



  • Turn on your camera by sliding the power switch to SETUP position. The camera will enter the setup mode and display the menu on the screen.



  • Launch the MMSConfig program on your PC. The program will automatically detect your camera and show its information on the window.



Configuring the camera settings with MMSConfig




Once you have connected your camera to your PC, you can use the MMSConfig program to configure the camera settings and send photos via SMTP protocol. Here is how to do it:



  • Select the COM port that corresponds to your camera from the drop-down list at the top of the window. If you are not sure which port to choose, you can click on the Auto Search button and let the program find it for you.



  • Click on the Read From Camera button to read the current settings of your camera and display them on the window. You can also click on the Default button to load the default settings of your camera.



  • Modify the settings according to your preferences and needs. You can change the parameters such as image size, video size, video length, PIR sensitivity, time lapse, timer, etc. You can also enter your email address and phone number that will receive the photos from your camera.



  • Click on the SMTP button to enter the SMTP settings that will enable your camera to send photos via email. You need to enter the SMTP server address, port number, user name, password, sender address, and receiver address for your email account. You can also choose whether to use SSL encryption or not. If you are not sure about these settings, you can consult your email provider or search online for some examples.



  • Click on the Write To Camera button to save the settings to your camera. You will see a message that says "Write OK" if the operation is successful.



Testing the camera and sending photos to your email or phone




After you have configured the camera settings with MMSConfig, you can test the camera and see if it can send photos to your email or phone. Here is how to do it:



  • Disconnect your camera from your PC and remove the USB cable.



  • Press any button on your camera to exit the setup mode and enter the preview mode. You will see a live view of what your camera sees on the screen.



  • Press OK button to take a photo manually. The photo will be saved on your SD card and also sent to your email or phone via SMTP protocol.



  • Check your email or phone and see if you have received the photo from your camera. If yes, congratulations! You have successfully set up your HC-700 M/G trail camera. If not, you may need to check your network signal, SIM card balance, SMTP settings, or contact customer service for help.



How to Use Your HC-700 M/G Trail Camera




Choosing a suitable location for your camera




To get the best results from your HC-700 M/G trail camera, you need to choose a suitable location for it. Here are some tips on how to do it:



  • Choose a location that has frequent animal activity or human traffic, depending on what you want to capture with your camera.



  • Avoid placing your camera facing directly into the sun, as this may cause overexposure or glare in your photos and videos.



  • Avoid placing your camera near sources of heat or light, such as fireplaces, lamps, or heaters, as this may trigger false alarms or reduce battery life.



  • Avoid placing your camera in areas with high humidity or moisture, such as swamps, rivers, or ponds, as this may damage your camera or affect its performance.



  • Avoid placing your camera in areas with strong electromagnetic interference, such as power lines, radio towers, or cell phone towers, as this may affect the network signal or the camera function.



Mounting the camera securely and adjusting the angle




After you have chosen a suitable location for your camera, you need to mount it securely and adjust the angle. Here are some tips on how to do it:



Use the strap that came with your


About

Welcome to the group! You can connect with other members, ge...

Members

bottom of page